Glaze N Seal Neutral Cleaner - Quart Safe, everyday cleaner for concrete, masonry, tile, natural stone. Lifts out dirt and grease on contact. Concentrated "no rinse" formula. Will not dull sealer or polish. Glaze ???N Seal Neutral Cleaner is a concentrated neutral cleaner designed for regular use as a maintenance cleaner. Neutral Cleaner is formulated with a special blend of powerful but mild detergents, and wetting agents that combine to loosen, lift and dissolve dirt and grease on contact. It dries clear and bright without leaving streaks or hazy residues. It may not require rinsing under normal conditions as part of a regular maintenance program. Will not dull existing wax or polish. Uses: On all types of hard surfaces including ceramic tile, vinyl, no wax floors, saltillo tile, brick, masonry, marble and other natural stone surfaces. Use also on walls, sinks & countertops. SPECIAL FEATURES. Safe, biodegradable cleaner No rinse formula Will not harm existing sealers, floor finishes or waxes Pleasant, fresh scent Regular use prevents buildup of soap scum, mineral deposits and algae 5,000 to 10,000 square feet per gallon. APPLICATION 1. Read entire label before using. 2. Sweep or vacuum surface clean. 3. Dilute 3-4 ounces of Glaze ???N Seal Neutral Cleaner with a gallon of clean water. (warm is preferred.) 4. Use a clean mop to spread the solution liberally on the floor. Damp mop away any puddles and allow the area to dry. 5. For heavy soiling, increase the amount of cleaner and use stiffer brush or scrubbing pad. Repeat if necessary. 6. For low foaming scrubbing machine use for floor cleaning add Glaze ???N Seal Neutral Cleaner to the tank at the lowest recommended dilution. Increase ratio if needed. 7. Ready for surface traffic in 30 minutes. . 8. Allow floor to thoroughly dry before applying any type of sealer or floor finish. LIMITATIONS ??? If floor has been neglected or especially tough soils (such as asphalt tracking or oil) are evident, a more chemically aggressive cleaning agent may be needed. ??? On floors that have repellent sealers or acrylic finishes this cleaner gives superior cleaning performance. On these floors rinsing is recommended after washing for best results. . ??? On sealed Saltillo tile floors frequent damp mopping with a minimum amount of water is recommended . KEEP OUT OF REACH OF CHILDREN READ COMPLETE INSTRUCTIONS BEFORE USING Safe to use in normal solution on any surface not harmed by water. ??? Not for use on humans or animals as degreasing agents in Neutral Cleaner will remove protective oils from skin. How to Remove Efflorescence & Mineral Deposits from Concrete & Masonry Surfaces

Modern Stones Grout Sealer Pro Water Base Available: Gallon, Quart, Pint, 5 gal Economical Pre-Grouting Sealer Professional Results . . . GUARANTEED! Modern Stone???s Grout Sealer Pro is a low odor, water based sealer, formulated to provide stain and oil repellency to grout and natural stone substrates with little or no change in appearance. It allows for moisture vapor transmission and may also be used as a pre-grouting sealer. Greatly reduces cleaning maintenance.. Uses: Marble, Limestone, Travertine, Concrete/Masonry, Saltillo, Clay Tile, Stucco, Terrazzo, Grout for Ceramic & Porcelain Tile Test in an inconspicuous area and allow 24 hours to cure to determine ease of application and desired results. VOC: 60 g/l Modern Stone???s Grout Sealer Pro is a low odor, water based sealer, formulated to provide stain and oil repellency to grout and natural stone substrates with little or no change in appearance. It allows for moisture vapor transmission and may also be used as a pre-grouting sealer. Greatly reduces cleaning maintenance. ??? No Gloss ??? Grout Sealer ??? Water Based Unsurpassed Water & Oil Resistance No Unpleasant Odor (very low odor) Pre-Grouting Sealer Safe to Use Easy to Apply Long Lasting Resists Mildew VOC Compliant Application 1. Ensure surface is clean, dry and free of waxes or coatings. 2. Apply sealer liberally using a grout roller, paint pad, brush, or low-pressure chemical sprayer. Focus application to grout joints. * Note: Do not allow excess sealer to dry on surface. 3. Allow sealer to dwell for up to 5-10 minutes. Remove excess with cotton bonnet pad or clean towels. Tiles should be completely dry and free of excess sealer. 4. Apply a second coat if necessary 30 minutes after initial application. 5. Buff surface for even luster. 6. Cure time: Ready for foot traffic in 2 hours. Fully cures in 24-48 hours. 7. Clean tools with water Covers Approximately 1000 to 3000 sq. ft per gallon. (Will vary widely depending on porosity and absorbency rate of surface to be sealed. Temperature and application method will also affect coverage.) Handling and Storage Close container after each use. Store in original container only. Keep in a dry, well-ventilated area. Avoid freezing or long-term high temperature storage. Do not place near heat, sparks, fame or other sources of ignition. DO NOT THIN OR DILUTE Caution: Rubber gloves and eye protection should be worn during application. Avoid contact with eyes and skin. Immediately flush eyes with water. If skin contact occurs wash with soap and water. Do not take internally. Do not induce vomiting. Seek medical attention. Modern Stone Product Coverage Chart Modern Stone Product Specifier Chart  

Modern Stones Revive Grout Cleaner Available: Gallon, Quart, 5 gal - Concentrated Professional Results . . . GUARANTEED! Modern Stone???s Revive is an acid replacement technology cleaner designed to etch grout, remove grout and mortar smears, mineral deposits and rust stains. This concentrated, salts-based cleaner is specially formulated to be highly effective with additional handling and safety benefits when compared to traditional acid-based cleaners. Revive???s breakthrough formulation is highly resistant against damaging stainless steel, chrome or brass. Uses: Grout Revive???s breakthrough formulation is highly resistant against damaging stainless steel, chrome or brass Application 1. Sweep or vacuum surface to remove loose debris. *Note: Mask on acid sensitive areas such as stainless steel and natural stone. 2. Dilute Revive with water depending on cleaning task. * Light cleaning: Mix 1 part with 10 parts water. * Medium cleaning: Mix 1 part with 6 parts water. * Heavy cleaning/etching: Mix 1 part with 3 parts water. 3. Apply solution to area and allow to dwell 3-5 minutes. DO NOT allow to dry on surface. 4. Agitate with soft-bristle brush or acid resistant scrubber. 5. Remove dirty solution using a wet/dry vacuum, sponge, or damp mop. 6. Rinse thoroughly with clean water to remove residual cleaner. 7. Dry surface with terry cloth towel or other absorbent materia Covers Approximately 1000 to 10,000 sq. ft per gallon. Handling and Storage Close container after each use. Store in original container only. Keep in a dry, well-ventilated area. Avoid freezing or long-term high temperature storage. Caution: PROTECT AREAS FROM OVERSPRAY. Rubber gloves and eye protection should be worn during application. Avoid contact with eyes and skin. Immediately flush eyes with water for 15 minutes. If skin contact occurs wash with soap and water. Do not take internally. Do not induce vomiting. Seek medical attention Use on acid-resistant tile, stone or masonry surfaces. A pre-test for resistance should be performed prior to use. Test in an inconspicuous area to determine ease of application and desired results. Warning: This product is not for use on natural stone surfaces such as flagstone, marble or limestone. If revive is sprayed or splashed on stainless steel, chrome or brass, simply rinse cleaner off metal with water. Modern Stone Product Coverage Chart Modern Stone Product Specifier Chart Revive Grout Cleaner MSDS

Wet Look Green Lacquer Lacquer Wet Look Film Forming Sealer Solvent Based VOC Content: 595 g/l The original "Wet Look" Lacquer provides beautiful high gloss protection to decorative concrete, masonry, and natural stone. For use on porous materials. A clear, non- yellowing sealer that resists tough oils, water and acid - indoors and outdoors. Deep bonding formula resists peeling, cracking, UV degradation and efflorescence. Great for driveways, patios, fountains, and ponds. Covers 125 - 500 Sq. ft / gal (1st coat) 50% greater on 2nd coat Dry Time - 1 hour Non-Yellowing Use Indoor or Outdoors Fast Drying and Long Lasting Apply with Brush or Sprayer Prevents Staining Strong Resistance to Efflorescence A revolutionary Low-VOC crystal clear acrylic coating designed to protect and beautify concrete, masonry and tile surfaces, This super-tough film gives a rich "Wet Look", resists chemicals, abrasion and stains. Click here for more information  

Modern Stones Reveal & Seal Enhancer Sealer Solvent Base Available: Gallon, Quart, Pint, 5 gal Professional Results . . . GUARANTEED! Modern Stone???s Reveal & Seal is a premium solvent based, enhancing sealer formulated to darken, highlight and enhance the beauty and character of natural stone. Reveal & Seal???s U.V. resistant formula provides maximum stain protection from oil and water based stains. It allows for moisture vapor transmission and can be used for indoor and outdoor applications. Uses: Marble, Granite, Limestone, Travertine, Quartzite, Slate, Sandstone Test in an inconspicuous area and allow 24 hours to cure to determine ease of application and desired results. VOC: 260 g/l A solvent-based enhancing sealer formulated to darken, highlight and enhance the beauty and character of natural stone. with very low odor. Use on marble, granite, limestone, travertine, concrete/masonry, saltillo tile, clay tile, stucco, terrazzo, and grout. Test in an inconspicuous area and allow 24 hours to cure to determine ease of application and desired results. ??? No Gloss ??? Enhancer Sealer ??? Solvent Based Unsurpassed Water & Oil Resistance U.V. resistant formula No Unpleasant Odor (very low odor) Safe to Use Easy to Apply Long Lasting Resists Mildew VOC Compliant Application 1. Ensure surface is clean, dry and free of waxes or coatings. 2. Agitate bottle before use. 3. Apply Reveal & Seal liberally using a paint pad, roller, brush, lambs wool applicator or low-pressure chemical sprayer. Distribute product evenly over entire surface to ensure uniform coverage and maximum penetration. *Note: Reveal & Seal provides maximum enhancement. A lighter first application may be recommended in order to determine substrate's porosity. Over applying enhancer may cause excess product to dwell on surface and make clean up more difficult. Do not allow excess sealer to dry on surface. 4. Allow sealer to dwell for up to 20 minutes, or until it begins to dry on surface. Remove excess with cotton bonnet pad or clean towels, until surface is completely dry. 5. For more porous substrates if darker appearance is required, apply a second coat 30 minutes after initial application. 6. Ready for foot traffic in 4 hours. Fully cures in 24-48 hours. 7. Clean tools with mineral spirits Covers Approximately 200 to 1500 sq. ft per gallon. (Will vary widely depending on porosity and absorbency rate of surface to be sealed. Temperature and application method will also affect coverage.) Handling and Storage Close container after each use. Store in original container only. Keep in a dry, well-ventilated area. Avoid freezing or long-term high temperature storage. Do not place near heat, sparks, fame or other sources of ignition. DO NOT THIN OR DILUTE Caution: Rubber gloves and eye protection should be worn during application. Avoid contact with eyes and skin. Immediately flush eyes with water. If skin contact occurs wash with soap and water. Do not take internally. Do not induce vomiting. Seek medical attention. Modern Stone Product Coverage Chart Modern Stone Product Specifier Chart Clear Guard Solvent MSDS  

Innovative Stone Gloss - Gallon High Gloss Floor Finish Stone Gloss is a synthetic blend of high gloss polymers, leveling agent and drying solvent. Stone Gloss contains a new generation polymer that is chemically programmed to keep the finish shining brighter and wearing longer. This product resist scratching and gives the floor an exceptionally long wear life. Stone Gloss Floor Finish sets a completely new standard for floor finishes. It can be used on slate and other rough textured and extremely porous stone and masonry surfaces as well as all resilient floors Vinyl asbestos, Asphalt tile, Vinyl sheet, Tile, Rubber, Reinforced vinyl and Linoleum. Pad Suggestions: Natural fiber pads are preferred for burnishing. A tan, beige or light blue synthetic pad can also be uses. Direction 1. Clear the area to be finished of all movable object. 2. Sweep the floor clean of loose dirt and debris. 3. Apply stripper and remove all old wax and floor finish. Repeat if necessary 4. Rinse the floor as thoroughly as possible and let dry. 5. Work with clean equipment and broom or microfiber mop on a thin coat of finish. Allow to dry thoroughly (at least 30 - 45 minutes) before applying another coat. 6. A minimum base of 2-4 coats is recommended. Maintenance Sweep daily with a dust mop or cloth. Clean with neutral pH cleaner with mop bucket or automatic scrubber. Light cleaning will remove surface soils and stains and maintain gloss and color. Dry buff or burnish with white pad after cleaning to obtain a wet look.

Coating Stripper for Natural Floors - Gallon Extra Active Stripper For use on Natural Floors --- Not to be used on travertine. ----- Coating Stripper is a special blend of Water Soluble solvents and surfactants designed to emulsify multiple coats of floor finish. Coating Stripper is effective at removing as many as 10 coats of floor finish. It should be used on vinyl composition tile and other floors that will not be harmed by water based solvents. DIRECTIONS: 1. To achieve best performance, experiment in small test area with various dilutions before applying generally. 2. Dilute before using. Do not use on painted surface or wooden floor. Use cautiously for stripping linoleum, Rubber or asphalt tile as stripper may cause bleaching, softening or bleeding. 3. Rinse immediately with water and pick up. Wipe up any spills or splashes from baseboards or painted surfaces immediately. For normal problem floors, dilute 1 part stripper to 4 parts warm water. Apply to small inconspicuous test area before doing entire floor. Dilution ratios ranging from 1:4 to 1:10 may be necessary depending on the number or coats of old finish. Do not use on painted surfaces or wooden floors. Use cautiously for stripping linoleum, rubber or asphalt tile as stripper may cause bleaching, softening or bleeding. Using determined dilution ratio, apply to small area of flooring (approx. 50-100 sq. ft.) Permit solution to remain on floor approximately 15-30 minutes before scrubbing. Do not allow solution to dry on floor. Scrub thoroughly with machine a stripping brush or pad. Pick up solution immediately with wet-dry vac or mop. Do not scrub with Monkey Pad as the stripper will unbond the diamonds rendering the pad useless. Rinse immediately with plain water (at least 2 times) and pick up. Wipe up any spills or splashes from baseboards or painted surfaces immediaely. Do not apply sealer or finish until floor is thoroughly dry and a small test patch is done with new finish to ensure proper bonding. Repeat as needed until all floor finish is completely removed. Automatic Scrubbers: Use the double pass method for best results. Apply stripping solution, normally 1 part stripper to 10 parts water. (Test in small area prior to stripping floor). Allow 15-30 minutes dwell time. Do not allow stripper to dry. Then strip with machine. CAUTION This product is intended for Industrial and institutional use. Although this is a mild chemical agent, It can cause irritation to eyes and skin. Avoid contact by wearing protective devices such as safety glasses and rubber gloves. If contact to eyes or skin, flush with water for 10-15 minutes. If irritation persists, seek medical attention. Always read the Material Safety Data Sheet for additional precautions before using this product. Coating Stripper for Natural Floors - MSDS