Showing 25–48 of 525 results

Sort by
ATR Leveling System T Spacers 3mm

ATR Leveling System T Spacers 3mm


ATR Tile Leveling System - 3mm

Floors and Walls

T Spacers 3mm

For use with brick pattern, subway layout, herringbone, etc.

Apex Coverage Area - 100 Pieces of tile compare at 33 pieces of tile with other leveling system

Tiling made easy with the ATR Tile Leveling System

T spacer 1/8" (3mm) - Tile thickness 15/64 - 51/64 (1/4 - 3/4) (6mm-20mm)

You only need 1 cross spacing plate for 4 tiles NOT 4 Clips like every other Leveling System

While every other system require 376 units for 100 pieces of tile ATR require only 117

Very easy to learn and use at any skill level

Advantages of the ATR Tile Leveling System

  • No Tools (GUN) needed! No need for expensive hand tools.
  • Simple and quick to lay with only 2 elements: Spacer & Spindle.
  • The only system that removed without the use of a force
  • Only System that leave clean grout line (no risk of spacers not break all the way)
  • Cross Spacers (+) Shape allow for 2/3 of saving
  • Creates a lippage free surface
  • Keeps tiles in place while drying
  • All-in-one grout spacing and tile alignment system
  • Stress free installation
  • Professional finishes every time
  • Very simple and easy to use
  • Saves time
  • Suitable for floors and walls
  • Suitable for indoor and outdoor uses
  • Re-usable spindle
  • Australian design and Australian made

Example of the different between ATR to other leveling system

100 pieces of tile project ATR use total of 117 spacers with approximately cost of $29.99 compare to any other leveling system 376 spacers with cost of $44.00

About 33% saving in money of spacers and over 66% time saving in Labor of saving on installing additional 259 pieces

How to use 5 Easy steps

1. Spread thinset install tile

2. Screw spindle into spacing plate, Slide spindle with spacing plate attached in between two tiles.

3. Tighten spindle clock wise firmly until all four corners are aligned flush.
* Remove Re-usable spindle once tile adhesive is dry.

ATR Leveling System, ATR Plastic, Tile leveling, lippage free, flat surfaces, Leveling System,

ATR Spacing Plate Calculator

Click Here to watch ATR Videos

ATR Leveling System Comparison Chart

ATR Leveling System Questions and Answers


Pocket Knife, 1 Unit

Pocket Knife, 1 Unit


Wire stripping notches on blade, stripping sizes 14-10 AWGSatin 440A stainless steel drop point bladeAnodized aluminum handle for corrosion resistanceDual thumb studs for one-hand openLiner lock secures blade in open positionPocket clip keeps knife readily availableGreat for stripping wire, splitting cable and performing everyday tasks

Screwdriver, 1/4-Inch Keystone Cushion-Grip , 1 Unit

Screwdriver, 1/4-Inch Keystone Cushion-Grip , 1 Unit


Heavy-duty square shank for wrench-assisted turningBolster reinforces shank for hard useDesigned for the most demanding usesCushion-Grip handle for greater torque and comfortPremium chrome-plated for smooth feel and corrosion resistanceInternal flanges inside handle provide solid, twist-resistant blade anchorSpecial heat-treated shaftsPrecision-machined tip for exact fitMeets or exceeds applicable ASME / ANSI specificationsTip-Ident?? quickly identifies the screwdriver type and tip orientation

Aluminum Swivel Mop and Pole

Aluminum Swivel Mop and Pole


Swivel Mop and Pole 18" Aluminum

18" Aluminum commercial grade swivel mop

16" Mop head fits 18" pads

Swivel & Pole Feature :

  • Universal handle adapter
  • Made for industrial & Commercial use
  • 360 degree motion
  • Sturdy Riveted Assembly
  • 3.5" Metal pin Swivel
  • Trapezoid shaped
  • Pole expend from 28" -70"
  • Pole 2mm aluminum tubing thick
  • Fits Velcro style pads 18" +

Rubber Mallet White Hammer

Rubber Mallet White Hammer


16 oz. Rubber Mallet

White Rubber will not mark surfaces

Continuer hardwood handles

Screwdriver, Multi-Bit, Nut Driver, 11-in-1, Ph, Sl, Sq, Torx Bits, 1 Unit

Screwdriver, Multi-Bit, Nut Driver, 11-in-1, Ph, Sl, Sq, Torx Bits, 1 Unit


Multi-bit screwdriver / nut driver shaft holds 8 popular tips and converts to 3 nut driver sizesIncludes industrial strength heat treated bits: 3/8-Inch, 5/16-Inch and 1/4-Inch nut drivers, #1 and #2 Phillips, 1/4-Inch and 3/16-Inch slotted, T10 and T15 TORX, and #1 and #2 square recessInterchangeable blade for fast and easy switch out; comfortable Cushion-Grip handleBlast finish bit tips provide a firm hold and reduce cam-out; Search Cat. No. 32526 for a full set of replacement bitsThe following replacement bits are available: see Cat. No. 32482 (#1 Phillips and 3/16-Inch Slotted), Cat. No. 32483 (#2 Phillips and 1/4-Inch Slotted), Cat. No. 32484 (#1 Square and #2 Square), and Cat. No. 32485 (T10 TORX and T15 TORX)TORX?? is a registered trademark of Acument Intellectual Properties, LLCAssembled in USA of US and imported components

Low Profile Utility knife

Low Profile Utility knife


Low Profile Utility knife

Product Features:

  • Quick change blade
  • Ergonomic comfort grip
  • Push button 5 blade storage in handle
  • Twine cutter

DTA Wedges Lippage Leveling System - Spacers 3mm

DTA Wedges Lippage Leveling System – Spacers 3mm


DTA Wedges Lippage Leveling System - Spacers - 1/8"

Three Part System with Wedge, Spacer and Gun that eliminate lippage in tile installation

Available 1/16" and 1/8"

Specifications :

Grout Joint 1/16" (1.5mm) Maximum - Tile Thickness 1/2" - Minimum Tile Thickness 1/8"

Grout Joint 1/8" (3mm) Maximum - Tile Thickness 1/2" - Minimum Tile Thickness 1/8"

Spacer - The spacer is inserted under the base of the Tile

Wedge - The wedge is use across the top of the Tile to hold the spacer in place and apply pressure while the tiles dry

Tool Gun - The tool gun is used to create tension on the wedge and spacer

Very easy to learn and use at any skill level


  • 3 Part System with Caps and Spacer that eliminate lippage in tile installation
  • Reusable Wedges
  • 40mm Adjustment
  • Ideal for Wall and Floor

How to use Wedges Lippage System

1. Place Lippage Spacer between tiles 4" from both ends of tile.
2. Once tile and spacer are in place, fasten the Wedges.
3. Clamp the two pieces together leveling the tiles, Using the Tool Gun, This will hold the tiles in place while the tile adhesive sets.
4. Once tile adhesive has dried, simply kick the Wedges along the grout joint to remove. Use white rubber mallet to remove from walls. Grout to finish tiled area.
5. Remove Wedges from floor for re-use


Copyright © 2022 AMAST. All rights reserved.

Submit you post here.

Please be patient after posting, because your article must be reviewd by one of our editors.
Thank you!

Please complete the required fields.
Please select your image(s) to upload.

New Account

Please complete the details below and we'll be in contact as soon as possible.