Search
Generic filters
Mosaic Glass and Marfil Marble Surface Waves – Beige
$64.00

Mosaic Glass and Crema Marfil Marble Surface Waves – Beige Water jet mosaic, painted beige glass and crema marfil marble in water wave interlocking pattern art mosaic. Price per Sheet Material: Glass and Crema Marfil Marble Piece Size: 11 1/2″ x 12 1/2″ Sq Ft Per Piece: 1 Thickness: 3/8″ Colors: Beige Artistic glass design forming a Surface Waves pattern Brighten up your bathroom, kitchen and shower with this series Aacceptable for use on shower walls and floors. The polyurethane cord backing makes installation easy. for use in Interior Dry Walls, Interior Floors, Shower Walls, Shower Floors Installation Guide Recommended Substrates: Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days). Cementitious backer units (CBU)-ANSI A118.9. Concrete slabs cured for 28 days minimum. Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04. Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas. Setting Materials & Methods: Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate. Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase. Only use setting materials that meet or exceed TCNA guidelines Only use an accredited licensed contractor experienced in the art of installing mosaic products. Setting methods must conform to the TCNA guidelines. Note: Grout Selection: The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. Maniscalco is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures. Measuring: Measure coverage area, make sure to purchase at least 10% extra material than is required. This will account for any breakage or mis-cuts during installation, and ensure you have extra material should you have to replace any tile elements in the future. Cutting: Plan the placement of the tiles on your wall prior to installation. If you need to cut a mosaic sheet, cut from the back using a utility knife between tiles along the grout joints. Should you need to cut across tiles in a fashion that is not possible with a utility knife, use a wet saw with a diamond blade to cut through the tile. Drilling: Using a drill bit designed for glass is recommended. When drilling the hole, keep the bit and hole lubricated to prevent chipping. Start by drilling from both ends of the tile, starting with the back and drilling half the depth of the tile. Then, turn the tile over and complete the hole is recommended. This will prevent the glass from chipping as the drill bit exits the tile. Applying Setting Materials: Apply setting material using the notched side of a V-notched trowel. Using the flat side of the trowels, smooth out all ridges to achieve a consistent, even 1/8??? (3mm) coverage. Apply glass mosaic sheets, mesh -side down, firmly into freshly laid setting material. Mix and match from assorted sell units to achieve consistent variation. Using a rubber grout float gently press the tile into adhesive to ensure complete contact. Natural Stone should be sealed prior to grouting. A premium penetrating sealer is recommended for a natural look. Please refer to sealer manufacturer???s recommendations for application instructions. Recommended Thin-Set: MAPEI Adesilex-P10 Premium Glass Tile Mortar mixed with MAPEI Keraply Latex Mortar Additive Suggested Grout: MAPEI Ultracolor Plus FA, MAPEI FlexColor CQ or BOSTIK Trucolor Rapidcure Cleaning: Clean all excess grout immediately with a damp sponge. After 12 hours polish off any remaining haze with a dry cloth or towel. For tough stains, we require the use of PH Neutral cleaner to clean the tile and grout, such as Grout & Tile neutral cleaner. Maintenance & Care Required to use a soft bristle brush to scrub the tile surfaces and grout. Take care to only use a soft bristle brush, to avoid the chance of scratching or damaging the grout. Then, simply wipe the surface, rinse well with clean water, and dry with a soft clean towel. Required to use PH Neutral Cleaner to clean the tile and grout, such as Grout & Tile Neutral Cleaner We strongly recommend customers to use a licensed tile contractor to do the tile installation and always use TCNA tile installation handbook as the installation guidance Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish

Copyright © 2022 AMAST. All rights reserved.

Submit you post here.

Please be patient after posting, because your article must be reviewd by one of our editors.
Thank you!

Please complete the required fields.
Please select your image(s) to upload.

New Account

Please complete the details below and we'll be in contact as soon as possible.